Combination Square Set
Combination sets are useful for all types of mechanical jobs. The set is comprised of a straight protractor is graduated to read from zero to 180 in both directions. The rule is made of stainless steel and is graduated in both 0.5mm and 1mm increments. The square head has a level and a scriber point. The protractor head, center head, and square head are all made of cast iron.
Precision Try Squares with Base
Recommended for use where extreme accuracy is required. Base and blades are hardened, ground and lapped to insure that the square has a straight, parallel setup. 1st and 2nd grades are available according to their tolerance. Non-graduated types are most commonly used but graduated types are also available upon request.
Carpenters’ Square
For carpenters or machinists use. Made of polished tool steel and graduated in 1mm increments.
Steel Straight Edge
Precision made of fine tool steel to industrial standards. The surface is ground and planed to a smooth surface. Perfect for use as a straight edge or as a level to check if surfaces are flat. The types shown above, the standard (rectangular) and beveled edge types without graduation are most common. Other types such as a fold out or I-beam straight edge with graduations are also available upon request.
Gasoline and Oil Finding Paste
A chemical paste used with oil gauging tape for measuring the presence of various types of oils. The colour of the paste will generally change from light blue to red upon contact with oil. This paste will detect almost any kind of oil including mineral oil, vegetable oil, animal oil and solvents such as benzol, alcohol, acrylic solution, alkaline solution and spirits.
Water Finding Paste
A paste for use with oil gauging tape. The colour of the paste will change from yellow to red upon contact with water.
Oil Gauging Tape
So called ullage tape. Made of steel or stainless steel with a chromed brass drawing weight attached. Metric or metric and inch graduated tapes are available. The tapes are mounted to a strong frame with a wooden carrying handle. Tapes of lengths up to 50mtr are also available upon request.
Measuring Tape
13mm wide measuring tape available in linen, steel or stainless steel. The tape is easy to ravel and unravel and the metric graduations are clearly visible. The tape is contained in a black, vinyl laminated, metal case with a flush handle.
Convex Ruler
Locking, power-return, white steel convex rule, 12mm (1/2″) wide flexible steel blade in a plastic case. Available in metric standard or in metric and inch sizes.
Folding Ruler
Available in stainless steel or wood, with machine marked graduations.
Stainless Steel Straight Ruler
These engineer’s precision rules are made of stainless steel and dull chromed to make the graduations easy to read. Graduated in increments of 0.5mm.
Hook Type Dial Spring Balance
Painted metal case with brass dial and white markings, shock absorbing mechanism and zinc plated hook. Multipurpose use (weighing cold stores, bulk foods, etc.).
Wire Gauge
For gauging steel wires, drill rods, sheets, plates and wires of non-ferrous metal.
Center Gauge
A handy gauge used for inspecting the center angles of the lathe and the angles of screw making tools. Available in 55 degree and 60 degree. Made of hardened steel.
Screw Pitch Gauge
Designed to quickly determine the pitch of nut, bolt, and screw threads.
Bearing Feeler Gauge
Used for measuring main bearing clearance of marine engine. When the rod “S” has been pressed through the pipe “R” can be pushed away from the brass by further pressing on the rod “S” and when a distance “a” is obtained it is easy to feel the fit of the feeler in the clearance.
Gap Gauge for Motor
Similar to feeler or thickness gauges but with longer leaves in order to measure between the stator and coil of a generator.
Thickness Gauge
Particularly popular with machinists and tool markers for gauging narrow slots as well as for adjusting the air gaps of valves on motors. The leaves are made of tempered steel and have the thickness marked on them. The gauges listed below are classified as A Type because they have straight leaves. Type B gauges with tapered leaves are also available upon request.
Vernier Depth Gauge
Made of hardened stainless steel. Graduated in increments of 0.05mm in metric sizes only.
Digital Calipers
A compact, easy to use caliper graduated in 0.01mm increments. All measures are shown on a digital display making it easier to take quick, precise measurements. The graphic display will indicate whether the tool is set for the measurement of inside or outside diameters.
Vernier Calipers
Made of high grade stainless steel with a satin chrome finish. Available in metric graduation, or metric and inch graduation.
Depth Micrometer
Measures the depth of holes, projections, etc. Provided with a hardened tip and threaded ground screw, adjustable for wear. The face of the bass is hardened and planed to maintain a level surface. Graduated in increments of 0.01mm
Jointed Inside Micrometer
Each set of the anvils for the jointed inside micrometers is adjusted to suit the particular micrometer. Each is given a marrk and must not be used on any other micrometer. When assembling, clean the joining faces perfectly. Graduated in 0.01mm increments
Tubular Type Inside Micrometer
A single rod type micrometer made from strong but light tubing. The measuring anvils are ground to a radius to be used on either flat or curved surfaces. Graduated in 0.01mm increments. Micrometers with counters displays are also available upon request.
Outside Micrometer with Interchangeable Anvil
Each micrometer is equipped with a series of interchangeable anvils. Each anvil is marked to show its capacity and is fitted with an adjustable collar to prevent wear. Graduated in 0.01mm increments.
Outside Micrometer with Counter
A numeral counter indicates sizes simulaneously as the measurements are being taken. The display is very easy to read. Graduated in 0.01mm increments from 25mm to 500mm on the standard size micrometer but micrometers up to 1000mm are also available upon request.
Outside Micrometer
Graduated in 0.01mm increments with standard measurement sizes from 25mm to 500mm. Micrometers measuring up to 1000mm are also available upon request.
Spring Divider
Made of hardened steel with points that are extra tempered for scribing on iron surfaces. Has a rigid spring and an adjustable quick setting screw.
Steel Compass
Made of hardened steel with points that are extra hard tempered for scribing circles on iron plates.
One-Side Calipers
For measuring the thickness of the walls of pipes or values, etc. Made of hardened steel with tempered steel points.
Spring Inside Calipers
Has point of a shape suitable to work in threads.
Inside Calipers
For measuring the inside diameter of pipes, fitting, etc. Made of hardened steel with points of tempered steel to prevent wear.
Spring Outside Calipers
For the outside measurement of threads. The tips are specially shaped shaped to fit suitably to the threads.
Outside Calipers
For the easy measurement of the outer diameter of pipes and other round objects. Made of hardened steel with tips of tempered steel.
Step Drill
Made of heat treated steel and can create various hole sizes by single drill in steel, stainless steel, plastic or wood up to 6mm depth.
Carbide Tipped Hole Saw
Made of a selected high speed steel or tungsten carbide tip for cutting smooth and accurate holes. Available cutting depth is 5mm for standard type hole saw and 38mm for deep cut type hole saw.
HSS Hole Saw
Made of a selected high speed steel or tungsten carbide tip for cutting smooth and accurate holes. Available cutting depth is 5mm for standard type hole saw and 38mm for deep cut type hole saw.
Valve Seat Cutter
These value seat cutting tools are easier than ordinary type cutters in assembly and handling for precision cutting work. Remove the value cap or flange and fit the suitable cutter to the spindle. Then, set the fixing bed using a tightening bolt for the cap or flange. Check that the cutter fits horizontally with the value seat and is in the center position. At this point you set the adjustable, begin the cutting operation by turning the handle clockwise. A standard set of 1″ to 4″ cutters.
Stock for Round Die
Adjustable handle for round dies. Select suitable diameter to fit your round dies.
Tap Wrench
The jaws are made of tool steel, carefully hardened and tempered for perfect performance. The handle is knurled for safe, easy operation.
Thread Restorer
A square bar type restorer with 8 different lands. Where a die cannot be used, a few easy passes with the apporpriate land of the restorer over the damaged face of a bolt or a pipe will restore the thread wihout reducing the diameter. As only the displaced metal removed, the original fit is preserved
Knurls for Knurling Holder
Individually hob-cut from extra high carbon tool steel. Heat treated, tempered and tested to obtain sharp, perfectly formed teeth in every knurl. Can be furnished in coarse, medium or fine grade and in either straight line or diamond pattern.
Knurling Tool Holder
Self centering knuckle or joint has ample bearings to resist the severe strains of both end and side thrust. 2 types, A & B are available. Please specify which type is required when ordering.
Boring Tool Holder with Square Shank Tool Bit
Quickly exchangeable caps, straight (90 degree) or angular (30 degree).
Spring Cut-off Tool Holders
This design relieves the cutter blade from excessive pressure, avoiding chattering and climbing of the blade during cutting operation. For holding plate tool bits.
3-Way Tool Bit Holder
A tool for holding square tool bits in three ways. Furnished with an allen hexagon key.
Cemented Carbide Tip
These carbide tips are used with carbide tipped turning cutters. Tips are fitted with cement.
Single Point Tools with Cemented Carbide Tip
For square shank holders. The carbide tips are finely ground to be ready for use and are covered with an easy to remove cellulose sheath. Choose the cutter most suitable for the work you are doing from the examples below. Please specify whether you require left or right hand tips.
Rectangular Tool Bit
High speed, steel tool bit material is not hardened as it is made for general use. The material is available in 2 types, square and rectangular, to suit the users requirements. These plates are supplied in 300mm length pieces.
Square Tool Bit Material
High speed, steel tool bit material is not hardened as it is made for general use. The material is available in 2 types, square and rectangular, to suit the users requirements. These plates are supplied in 300mm length pieces.
Plate Cutting-off Tool Bit
For use in cutting hard materials like heat-treated alloy steels. die steels, bronze, stainless steels, etc. Ground on all 4 sides. Cut to standard tool holder lengths with a standard bevel on each end. Bits require grinding only to make them ready for use in tool holders.
Rectangular Plate Tool Bit
For use in cutting hard materials like heat-treated alloy steels. die steels, bronze, stainless steels, etc. Ground on all 4 sides. Cut to standard tool holder lengths with a standard bevel on each end. Bits require grinding only to make them ready for use in tool holders.
Rectangular Flat Tool Bit
For use in cutting hard materials like heat-treated alloy steels. die steels, bronze, stainless steels, etc. Ground on all 4 sides. Cut to standard tool holder lengths with a standard bevel on each end. Bits require grinding only to make them ready for use in tool holders.
Square Tool Bit
For use in cutting hard materials like heat-treated alloy steels. die steels, bronze, stainless steels, etc. Ground on all 4 sides. Cut to standard tool holder lengths with a standard bevel on each end. Bits require grinding only to make them ready for use in tool holders.
Carbide Rotary Bur
Designed for the efficient, bevelling of gears, burning, planing, shaping and milling, These rotary burs are advantageous for use with portable grinding tools of 10000 R.P.M. or more. Please specify the type, size of the blade and the shank when ordering.
Screw Extractor Set
With the screw extractor, the broken bolt or screw threaded hole can be easily removed without injuring threads.
Bevel Rolling Center
Used in combination with a lathe or an external grinding machine, the bevel rolling center serves as a center pusher for steel pipe or a workpiece with a large central opening and without a centering hole.
Rolling Center
Specially designed to withstand high-speed heavy-duty operations. Incorporated are a taper roller bearing, thrust ball bearing, ball bearing and other special bearings.