Stainless Steel Side Cutting Pliers
Various stainless steel tools are available and they show the following characteristics.
1) Resistant to corrsion and avoid steel material from corrosion in use.
2) Retain heat. Nd heat is difficult to be transmitted.
3) Higher rigidity than steel material.
4) Difficult to conduct electricity compared to copper.
5) Simple cleaning.
Stainless Steel Diagonal Cutting Pliers
Various stainless steel tools are available and they show the following characteristics.
1) Resistant to corrsion and avoid steel material from corrosion in use.
2) Retain heat. Nd heat is difficult to be transmitted.
3) Higher rigidity than steel material.
4) Difficult to conduct electricity compared to copper.
5) Simple cleaning.
Stainless Steel Adjustable Wrench
Various stainless steel tools are available and they show the following characteristics.
1) Resistant to corrsion and avoid steel material from corrosion in use.
2) Retain heat. Nd heat is difficult to be transmitted.
3) Higher rigidity than steel material.
4) Difficult to conduct electricity compared to copper.
5) Simple cleaning.
Stainless Steel Open & 12 Point Box Wrench
Various stainless steel tools are available and they show the following characteristics.
1) Resistant to corrsion and avoid steel material from corrosion in use.
2) Retain heat. Nd heat is difficult to be transmitted.
3) Higher rigidity than steel material.
4) Difficult to conduct electricity compared to copper.
5) Simple cleaning.
Non-Spark Heavy Duty Beryllium Copper Alloy Knife
Edged cutting blade length is 150mm and overall length is 265mm.
Non-Spark Fibreglass Square Scoop and Shovel
Made of fibreglass, a non-sparking safety tool, also will not scrape or strip the protective coating of a tank when sludging. Heavy duty, lightweight and most suitable tool for sludging oil tanks. Available in Scoop & Shovel.
Non-Spark Square Shovel
One type of non-spark tools are available, a special aluminum bronze material. This tool is non-magnetic and non-corrosive. The sizes of the item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Slotted Screwdriver Plastic Handle
The sizes listed below are of blade size only, not overall length.
Non-Spark Diagonal Cutting Pliers
This heavy duty diagonal cutting pliers is designed for cutting hard wires, etc. at close quarters.
Non-Spark Radio Pliers
Long thin taper nose for use in close quarters. An ideal tool for quick electrical and repair works.
Non-Spark Side Cutting Pliers
A non-sparking tool with powerful leverage and rigid side cutters.
Non-Spark Hand Scraper with Handle
Designed for scraping in areas where non-sparking tools are required.
Non-Spark Cold Chisel
To be used on jobs where non-sparking cold chisels are required.
Non-Spark Claw Hammer
One side for hammering and the other for pulling out nails.
Non-Spark Chipping Hammer
Designed for chipping of scale, rust or old paint in vessels where non-sparking safety tools are indispensable.
Non-Spark Testing Hammer
Reliable testing hammer will not produce sparks.
Non-Spark Ball Pein Hammer
Reliable ball pein hammer, will not produce sparks.
Non-Spark Allen Hexagon Wrench
One type of non-spark tool is available, a high quality grade beryllium copper alloy material. This tool is non-magnetic and non-corrosive. The sizes of this item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Socket Wrench Set
Able to furnish 12.7mm square drive set only.
Non-Spark Straight Pipe Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material, and a special aluminium bronze material. These tools are non-magnetic and non-corrosive. The sizes of the item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Ratchet Wrench
The size of this wrench is determined by its opening across flats, not by bolt diameter.
Non-Spark Adjustable Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material, and a special aluminium bronze material. These tools are non-magnetic and non-corrosive. The sizes of the item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Striking Ring Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material and a standard grade aluminum bronze alloy. These tools are non magnetic and non corrosive. The sizes of the items specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Striking Open Wrench
One type of non-spark tools are available, a high quality grade beryllium copper alloy material. This tool is non magnetic and non corrosive. The sizes of this items specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Double Offset Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material, and a special aluminium bronze material. These tools are non-magnetic and non-corrosive. The sizes of the item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Single End Wrench
One type of non-spark tools are available, a high quality grade beryllium copper alloy material. This tool is non-magnetic and non-corrosive. The sizes of this item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Double Open End Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material, and a special aluminium bronze material. These tools are non-magnetic and non-corrosive. The sizes of the item specified below are standard, but larger or smaller sizes are available upon request.
Non-Spark Single Open Wrench
Two types of non-spark tools are available, a high quality grade beryllium copper alloy material and a standard grade aluminium bronze alloy. These tools are non magnetic and non corrosive. The sizes of the items specified below are standard, but larger or smaller sizes are available upon request.
Blind Rivets
High strength, precision-made hollow rivets assembled on a solid mandrel. They are specially useful for “blind” fastening where no access to reverse side available. Rivets are made in various sizes with head styles in aluminum, steel, morel, copper and stainless steel. Two types of standard rivets, open and closed, are available but the most common open type is described below.
Kinetic Rim Gun Set
These “rim guns” are specially designed for clearing clogged drains by means of a compressed “air shot”, which strikes the water on top of the clogged part inside the pipe or drain. The result of this “air shot” is a wave of kinetic energy striking the resistance point vertically with high pressure and clearing the waste are clogged parts away.
Snake Wire Pipe Cleaner
Used for unclogging pipes and drains. The flexible coil of non-corrosive spring steel will remove most obstructions. The wire spring is available in diameters from 6mm to 13mm.
Flange Jack
The jacks exert tremendous pressure smoothly and evenly. The flange are parked quickly and held in perfect alignment without damage to flange faces.
Hydraulic Nut Splitter
Splits frozen or rusted nuts without damage to the bolt. It is conveniently sized to work in hard to reach places. Made of the finest long service.
Portable Hydraulic Jack
Made with a forged steel base, tool steel pump piston, and a high quality pump cup packing. A bronze guide bearing is used at the bottom of the precision ground ram. The ram cup is steel forged. Fixed with a hardened release, lowering valve. The handle is a knurled, interlocking type.
Hydraulic Bearing Puller
Designed for the removal of frozen bearings, wheels and other gears of various sizes without hammering or heating. 2 and 3-arm coupling pullers are available in capacities of 10, 20 and 50 tons. They are lightweight and have a compact design. Any hand or motor jump with a sufficient oil capacity may be connected to the puller.
Bearing Puller Set
The slide hammer bearing puller set has been designed for removing “hard-to-pull’ bearings without damaging the bearing housing. Expansion grippers are available from No. 00 to 06. These numbers 00 to 06 are indicating the last two numbers of the bearing number. When ordering, please make sure to indicate the last two bearing figures to get the right tools for your work. The expansion grippers are drop forged from vanadium alloy steel, heat-treated and chromed plated.
This bearing puller kit has been designed to remove the inner and outer bearing rings from bearing mounted to various fittings, shafts, etc. Made of drop forged, heat-treated vanadium alloy steel.
3-Arm Gear and Wheel Puller
Drop forged from vanadium steel. This rigid 3 arm puller has been designed for situations where the use of a 2 arm puller is not possible.
2-Arm Gear and Wheel Puller
Specially designed for LNG-LPG vessels and tankers, but also essential for factories handling explosive materials. Made of beryllium material except for the gears which are tightly covered by copper alloy casing assuring no sparking during operation.
Chain Hoist
Specially heat-treated and proof tested steel chain hoists equipped with a safety guard. These hoists can be operated at any angle and are equipped with a slip steel bolt which allows easy replacement of the load chains. The load wheel operates on precision ball bearings which are sealed with lubrication inside to eliminate the adverse effect of particles and dust on the moving parts. The top and bottom hooks are swivel type to allow easy turning of the load. These hoists have superior working capacities.
Hand-Lever Hoist
This lightweight, extremely durable portable chain hoist is easy to operate in pulling, hoisting and hauling jobs on deck or when moving machinery parts in the engine room. The ratchet action enables you hoist easily with short handle strokes and the load is constantly supported while lifting by a braking mechanism. The handle is opreated in the same way when lowering the load. The hoist is steadily lowered and the ratched system again assures that the handle will not spring loose and injure the operator. All hoist are tested at weighs 50% over the mentioned capacity for safety reasons.
Cut-Off Wheel
These resin bond cutting wheels have a big advantage over rubber cut-off wheels. They resist very high an aggressive cutting action, and a longer disc file. Grain No. 36 (medium grain) is recommended for general purpose ships use.
Abrasive Wheel
Aluminum oxide abrasive wheels. Available in various diameters, thickness and grits. Used with bench grinders.
Grinding Wheel
Grain size No. 36 is widely used on ships for all purpose grinding and cutting jobs.
Carborundum Round Edge Slip
A useful abrasive carborundum stone for grinding or edging of tools with curved edges. Maybe used dry or with a moderate application of oil.
Carborundum Oil Stone
For carpenters and engineers. May be used dry or with oil or water. Sufficiently porous to assure a good grinding or cutting action in combination with wax or oil.
Abrasive Sandpaper
Ideal abrasive for hand sanding wood, paint fillers, paint under coats and varnishes.
Sanding Disc
Designed for use with portable grinding machines on all kinds of surfaces. Each individual cutting grain is firmly anchored in a resin type adhesive that withstands high grinding heat.
Grinding Wheel Dresser
Designed for dressing the round grinding stone. Cutter is attached to the bush of the hardened steel case and the bush rotates on the shaft. Attached dust-proof washer is inserted on both sides of the bush to prevent intrusion of sand grains.
Hand Grinder
With a large strong built frame, heavy duty clamp and adjustable screw. The wheel has medium grit and operates accurately due to a well balanced gear.
Mounted Wheel
The mounted wheels are designed for use when ordinary grinding wheels cannot be used. Used in connection with air or electric drilling machines of 6mm capacity. Please specify the number of the required shape.
Mounted Wheel
The mounted wheels are designed for use when ordinary grinding wheels cannot be used. Used in connection with air or electric drilling machines of 6mm capacity. Please specify the number of the required shape.
Mounted Wheel
The mounted wheels are designed for use when ordinary grinding wheels cannot be used. Used in connection with air or electric drilling machines of 6mm capacity. Please specify the number of the required shape.
File Handle
Well balanced and shaped handle made of moistured absorbed hard wood.
Electroplated Diamond Needle File Set
The electroplated diamond needle file set is used by metal workers for precise filing on stone, metal, glass and sculptures. They are also ideal for delicate filing, shaping and creating inside cuts.
Needle File Set
File sets which are used for precision work. Available in industry-common sizes, in sets of 10’s.